INDUSTRIAL POLYCHEMICAL SERVICE -- WELD-ON 717 FOR PVC PLASTIC PIPE  -- 8040-00N000198
<pre>=====================  Product Identification  =====================

Product ID:WELD-ON 717 FOR PVC PLASTIC PIPE
MSDS Date:01/01/1987
FSC:8040
NIIN:00N000198
=== Responsible Party ===
Company Name:INDUSTRIAL POLYCHEMICAL SERVICE
Address:17109 S MAIN
Box:379
City:GARDENA
State:CA
ZIP:90247
Country:US
CAGE:17510
=== Contractor Identification ===
Company Name:IPS CORPORATION
Address:17109 S. MAIN ST.,
Box:379
City:GARDENA
State:CA
ZIP:90248
Country:US
Phone:310-898-3300
CAGE:17510

=============  Composition/Information on Ingredients  =============

Ingred Name:METHYL ETHYL KETONE (2-BUTANONE) (MEK)  (SARA III)
CAS:78-93-3
RTECS #:EL6475000
OSHA PEL:200 PPM/300 STEL
ACGIH TLV:200 PPM/300STEL 9192
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS

Ingred Name:CYCLOHEXANONE  (SARA III)
CAS:108-94-1
RTECS #:GW1050000
OSHA PEL:S, 50 PPM
ACGIH TLV:S, 25 PPM; 9293
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS

Ingred Name:POLYVINYL CHLORIDE RESIN (CAS#:9002-86-2) (W/INERT FILLERS
    & PIGMENTS)
RTECS #:KV0350000

Ingred Name:TETRAHYDROFURAN  (SARA III)
CAS:109-99-9
RTECS #:LU5950000
OSHA PEL:200 PPM/250 STEL
ACGIH TLV:200 PPM/250STEL;9192
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS

=====================  Hazards Identification  =====================

Effects of Overexposure:W/SEVERE OVEREXP,POSS NAUS,DIZZ,HEADACHE.POSS
    NARCOSIS,EYE,SKIN&NASAL PASSAGE IRRIT. (SEE OTHR PREC)

=======================  First Aid Measures  =======================

First Aid:INHAL:IF OVERCOME BY VAPS,REMOVE TO FRESH AIR.GIVE ARTIFICL
    RESP/O*2 AS NECESSARY.CALL PHYS.SKIN:REMOVE CONTAM
    CLOTHES&SHOES.WASH SKIN W/PLENTY H*20 15 MIN.EYE:FLUSH W/PLENTY
    H*20 15 MIN,CALL PHYS.ING EST:IF SWALLOW,DONT INDUCE VOMITING.CALL
    MD IMMED.

=====================  Fire Fighting Measures  =====================

Flash Point:6-8F (TCC)
Lower Limits:2.0
Upper Limits:11.8
Extinguishing Media:DRY CHEM,CO*2,FOAM-ANSUL "PURPLE K"-NATL
    AER-O-FOAM,H*20 FOG
Fire Fighting Procedures:EVACUATE ENCLOSED AREA.STAY UPWIND.CONFINED
    (SEE SUPP DATA)
Unusual Fire/Explosion Hazard:FIRE HAZ BECAUSE OF LOW FLASH PT&HIGH
    VOLATILITY.VAPS HEAVIER THAN AIR&MAY TRAVEL TO IGNITION SOURCE

==================  Accidental Release Measures  ==================

Spill Release Procedures:ELIMINATE ALL IGNITN SOURCES.AVOID INHAL
    VAPORS.KEEP LIQ OUT OF EYES.FLUSH W/LRG VOLUME OF H*20.CONTAIN LIQ
    W/SAND OR EARTH.ABSORB W/SAND OR NONFLAMMABLE ABSORBENT
    MATL&TRANSFER INTO STEEL DRUMS FOR R ECOVERY/DISPOSAL.PREVENT LIQ
    FROM ENTERING DRAINS.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN SHADE @40F-110F.KEEP FROM
    IGNITN SOURCES.AVOID PRLNG INHAL OF VAP.USE W/ADEQ VENT.FOLLOW
    PRECAUTN ON LABEL.ELECTRICALLY GROUND HANDLING EQUIP
Other Precautions:EFFECTS OF OVEREXP:DEFATS TISSUE.COND TO
    AVOID:SOURCES.THIS LIQ VERY STABLE AT NORM AMBIENT
    TEMP.INCOMPAT:CMPDS,STRONG
    OXIDIZERS,ISOCYANATES.SOLUBILITY:SOLVENT-COMPLETE,PVC
    RESIN-SEPARATES OUT

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR FOR ORGANIC
    VAP FOR CONFINED AREA
Ventilation:PREFER LOCAL EXHAUST.PROVIDE ADEQ VENT,KEEP VAPOR CONC <
    TLV
Protective Gloves:RUBBER OR PVA
Eye Protection:CHEMICAL WORKERS GOGGLES
Other Protective Equipment:IMPERVIOUS APRON (IF NEEDED)
Supplemental Safety and Health
BOILING PT&VAPOR PRESS:BASED ON FIRST BOILING COMPONENT,THF. SPECL FIRE
    FIGHT:AREA REQ SCBA,POSITIV PRESS HOSE/AIRLINE MASK.H*20 SPRAY
    TO:COOL CNTNR,FLUSH SPILL FROM IGNITN SOURCE,DISPERSE VAP

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:151F,66C
Vapor Pres:143
Vapor Density:2.49
Spec Gravity:0.958
Evaporation Rate &amp; Reference:5.0-8 (BUAC)
Appearance and Odor:CLEAR OR GRAY,MEDIUM SYRUPY LIQUID,ETHEREAL ODOR.
Percent Volatiles by Volume:90%

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
CAUSTICS,AMMONIA,INORGANIC ACIDS,CHLORINATED (SEE OTHR PREC)
Stability Condition to Avoid:KEEP FROM HEAT,SPARKS,OPEN FLAME&OTHR
    IGNITN (SEE OTHR PREC)
Hazardous Decomposition Products:WHEN FORCED TO BURN,PVC GIVES OUT
    CO,CO*2,HCL & SMOKE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT,SPARKS,OPEN
    FLAME&OTHER IGNITION SOURCES

====================  Disposal Considerations  ====================

Waste Disposal Methods:FOLLOW LOCAL,STATE & FEDERAL REGULATIONS.
    CONSULT DISPOSAL EXPERT. CAN BE DISPOSED OF BY INCINERATION.
    EXCESSIVE QUANTITIES SHOULD NOT BE PERMITTED TO ENTER DRAINS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.